What made this commission special was that both of them are longtime friends, and I was given carte blanche in designing the piece, with the caveat that the table would compliment their existing furniture. I chose some well-seasoned walnut with nice figure for the table, and black cherry as an accent wood. The pull on the drawer is made from an antique shank button.
After the drawings are complete, I sit with a cup of coffee and consider what I may have missed – a cautious second look. It gives me a chance to re-think my choice of materials and construction techniques. Where possible, I rough dimension good, dry stock, and then let it sit for a day or two before final surfacing and dimensioning. This releases any interior stress. You may find it convenient to mill pieces of the same thickness together. For example, begin with the legs, which are the thickest. Then mill the 11⁄16" material, followed by the 5⁄8", 1⁄2", 3⁄8", and finally, 1⁄4" material. Cut the stock a little longer than the finished length, and trim the pieces during the construction stage. I also make sure to match and mark all pieces so there is no confusion during the assembly process.
The rails are relatively thin on this table, so I cut the tenons closer to the inside edge, leaving a 1⁄8" shoulder on the inside. The width of tenons for this project is 1⁄4" with a 3⁄8" tongue, and the mortises are cut to a depth of almost 1⁄2". This allows for excess glue to accumulate in the mortise, rather than be forced out and onto the project surface. I do all mortising first, and then cut the tenons to fit. I thin stock, for the tails of the dovetail joints, by about 1⁄16" on the inside edge of both the full and half blind dovetails. This greatly eases marking for the pins, and helps gives a nice clean finished inside edge after glue-up.
You don't have to be confined to the dimensions in the materials list, or the selection of wood. Adding a few inches to the height, for example, would make this a wonderful entrance table.
• Mark leg (A) orientation, selecting the best face for the fronts.
• Cut the mortises.
• Cut the half blind dovetails.
• Mark the bottom center of each leg (A), and pencil in the location for the 11⁄16" foot detail.
• Mark a pencil line around each leg, 3 1⁄8" down from the top.
• Taper one side of the legs between the two pencil lines. I use a hand plane, beginning at the bottom section of the leg, gradually enlarging the planning area until I work up to the 31⁄8" pencil mark. Check with a long straight edge to ensure the taper will finish both straight and square. Clamping all four legs together and planning them as a unit, can make this easier, assuming that no tear-out is occurring.
• After the first side is complete, rotate the leg and taper the opposite side. To plane the remaining two tapers, add a spacer between the legs to fill the gap left by the taper so the legs remain positioned as if they were fully dimensioned. Place a support block under the legs to prevent downward arcing while you are planing.
• Carefully measure the placement for the kicker (F) and runner (G).
• Cut side rails (B) to size. Locate the tenon so that these rails will sit flush with the outer edge of the legs when finished. This may result in a 1⁄8" shoulder on the inner tenon side.
• Cut tenons on the back (C) and front (D, E) rails. The front top rail (E) requires you to cut a tail for the half blind dovetails. I then use this to mark, and finish the half blind dovetail pins on the front legs.
Kicker and Runners
• Drill two slightly oversize holes in the kickers (F), close to the outside edge, to accept a #8 screw, which attaches the table top to the main carcass.
• Cut out a notch at the rear leg end of the kicker to allow a snug fit against the side rail.
• Cut the tenons on both the kickers (F) and runners (G) to size.
• Glue the drawer guides (H) to the outside edges of runners (G). Dry fit the carcass to insure that the guides fit between the legs and are square to the runners.
• The top is built similar to a frame and panel door. When assembling the top, take into consideration dimensional change of the insert (I), which will vary with local climate, the cut of the lumber and the season in which you are constructing the table. In Saskatchewan, the tangential cut cherry insert will move about 5⁄32" in width over the year.
• Cut mitres on the frame pieces (J, K).
• Cut dadoes into the frame pieces to accommodate the insert. Ensure the insert is flush with the top of the frame.
• Use biscuits to join the mitred corners of the frame. (You can use either R3 mini or 0 sized biscuits). Be careful in the placement of the biscuits, since the outside
top edges of the frame are chamfered to a thickness of 1⁄2" to soften the edge.
• The kickers and runners, when installed, determine the inside space into which the drawer will fit and slide.
• Cut a piece of scrap plywood or MDF, to the size of the drawer footprint, and use it as a guide during assembly. This is a great help in squaring the table and
ensuring the proper placement of the drawer guides.
• Sand all the carcass pieces.
• Dry fit the pieces, making any adjustments to achieve a perfect fit.
• Glue and clamp the carcass. I prefer to enjoy this process and since I am not a fan of stress I like to work slowly and precisely. I use regular epoxy or a polyurethane based glue to give me plenty of open time, applying only enough glue to the joints to keep squeeze out to a minimum during clamping.
• I made the drawer sides (N), back (M), and bottom (O) with quarter sawn sycamore, which highlights the dovetails against the walnut drawer front (L). I then attached a walnut false front (P) to the drawer front. If you prefer, substitute Baltic birch for the drawer bottom.
• Cut the through dovetails and pins by hand or with a router jig.
• Drill holes through the drawer front (L) to accommodate #8 screws, for later attachment of false front (P).
• Rout grooves near the bottom of the sides and drawer front to accept the drawer bottom (O).
• Ensure that the drawer bottom can move under the drawer back (M) when assembled. This will allow for seasonal movement of the bottom drawer panel (O).
• Dry assemble the drawer to ensure that everything fits nicely, bearing in mind that the finished drawer should slide in and out of the table with very little movement laterally or vertically. You may need to do some final custom fitting of the drawer after glue-up.
• Rub paraffin wax on the runners and kickers to help the drawer glide smoothly. Chamfer the false drawer front (P) around the outside edge, and screw it into place, allowing for clearance below the tabletop.
• Attach a drawer pull and or a handle of your choice. I drilled two small side-by-side holes into the center of the drawer front (P) to accept a shank button, which I
glued in place using 5-minute epoxy.
• I applied 3 coats of Minwax Polycrylic to the top, allowing the final coat to fully dry before the wax finish was applied. I finished the rest of the table with wax to bring out an aged look with a soft sheen. All inside surfaces were finished similarly to the exposed surfaces. Wax enhances the walnut by deepening the colour and adding lustre to the finish.
At the end of the day I often reflect on the joys and challenges of woodworking, and share my thoughts with my wife Genevieve.
While working on this table I was stumped when it came to the drawer pull. I just could not design or find one that suited the piece.
After some consideration, Genevieve suggested a shank button. She has a collection of such buttons and offered an antique one (circa 1950) that was just perfect for this table. Although most shanks on buttons are best suited for use by smaller hands, the selection of buttons is endless, and can add a nice personal touch.
AS A SUBSCRIBER YOU GET 6 ISSUES PLUS
Bonus 45-page eBook: Essential Workshop Jigs and Techniques
Use of Canadian Woodworking's Website and It's Content
This website is presented with the understanding that:
The authors, editors and related web personnel are not responsible for the results of any actions taken on the basis of information on this website, nor for any errors or omissions;
This website is not engaged in rendering professional advice/services; and
Any and all content submitted by this website's users is in no way an expression of the beliefs or opinions of the owners, webmasters, authors and editors.
Canadian Woodworking disclaims all liability for any claim in relation to:
• any matters or factors outside of its control, including the availability or unavailability of the website and digital content due to the availability of the Internet, or telecommunications or other infrastructure systems; for any reasons including but not limited to power outages and maintenance.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Use of Canadian Woodworking site and Forum
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
CanadianWoodworking never shares, sells or rents your information to any third party without your permission.
This statement explains how we collect information from you and what we do with that information.
This policy does not apply to the practices of companies that CanadianWoodworking.com does not own or control, or to people that CanadianWoodworking.com does not employ or manage.
Information Requests and Use
CanadianWoodworking.com collects personally identifiable information when you use certain CanadianWoodworking.com services, when you visit CanadianWoodworking.com pages, and when you enter promotions or sweepstakes. CanadianWoodworking.com may also receive personally identifiable information from our business partners.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience.
CanadianWoodworking.com also automatically receives and records information on our server logs from your browser including your IP address, CanadianWoodworking.com cookie information and the page you requested.
CanadianWoodworking.com uses information for three general purposes: to customize the advertising and content you see, and to fulfill your requests for certain products and services.
The personal information that we retain is what is provided by you voluntarily. We use it to send you information about Canadian Woodworking and its products or to correspond with you regarding your subscription. If you are a subscriber we need this information to be able to deliver you our product(s) and service your subscription.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email firstname.lastname@example.org and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
Aggregate information is information that cannot identify you personally. We collect information on our subscribers that may be used in summary reports presented to our advertisers. This information helps them to better understand our audience and provide advertisements that are more likely to be of interest to you and your organization.
Our intention is always to gather information that will help us serve you better and never to gather information without your knowledge.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected. We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
Information Sharing and Disclosure
CanadianWoodworking.com will not sell or rent your personally identifiable information to anyone.
CanadianWoodworking.com will send personally identifiable information about you to other companies or people when:
We have your consent to share the information;
We need to share your information to provide the product or service you have requested;
We need to send the information to companies who work on behalf of CanadianWoodworking.com to provide a product or service to you. (Unless we tell you differently, these companies do not have any right to use the personally identifiable information we provide to them beyond what is necessary to assist us.);
We respond to subpoenas, court orders or legal process; or
We find that your actions on our web sites violate the CanadianWoodworking.com Terms of Service or any of our usage guidelines for specific products or services.
CanadianWoodworking.com may set and access CanadianWoodworking.com cookies on your computer.
Cookies are small text files that most Web sites, including canadianwoodworking.com place on your computer. Cookies help us identify your interests. They also prevent you from having to register repeatedly on canadianwoodworking.com or from repeatedly seeing the same ads.
Third party advertising
If you submit your name through a form on our website to request information from an advertiser or third party, canadianwoodworking.com is not responsible for any marketing or other use of your name by that third party.
In certain areas CanadianWoodworking.com uses industry-standard SSL-encryption to protect data transmissions.
Questions or Suggestions
If you have questions or suggestions please contact us.