MAKE A CHARCUTERIE BOARD WITH DRAWERS | Canadian Woodworking & Home Improvement

Sitting down to enjoy delicious food and quality time with guests is great. Even better is being able to deliver a charcuterie board everyone can eat from.

CHARCUTERIE BOARD WITH DRAWERS

MAKE A CHARCUTERIE BOARD WITH DRAWERS



Photos by Robert Zakarian
 
INFO:DIFFICULTY – 2/5, LENGTH/TIME – 2/5, COST – 2/5

I was in the market for a cheese serving board, however all the boards I found in stores were quite small and not what I was looking for. It was a great opportunity to design and make a custom board. This board measures 45" in length by 11-1/4" in width and is 4" in height.
 
Wood selection
I used solid maple for this project. The drawer fronts are solid walnut for accent. Pretty much any wood will do. You could choose a bold wood like padauk or zebrawood, but I thought that approach was a bit too over-the-top for my taste. To each their own. Using a closed-grain wood is likely best, as there’s less chance food will get left in the grain to grow bacteria. Although wood is natu­rally resistant to that sort of thing, I prefer to be on the safe side.
 
Make the top
The top is 45" long and 11-1/4" wide. The final thickness is 1-1/4". I dressed four boards to about 2-1/2" wide, then glued them up to exceed the final width. When dry, I sent the plank through my thickness planer and cut it to final size. Rout a pleasing edge around the upper perimeter of the top. I opted for a 1/4" chamfer.
 
Four supports
Another custom thought I had while making this board was including storage. I added two drawers to keep assorted serving utensils organized and nearby. The drawers could be made to what­ever size you like. I made these drawers with the size of my utensils in mind. I decided to attach four supports to the underside of the top. Their function was two-fold. First, they would support the top. Second, they would have grooves in their sides that would guide and support the two simple drawers. 
 
Though there are a number of options, I decided to use sliding dovetails to fasten the supports to the underside of the top. I cut the four supports to size, keeping in mind the extra material needed for the sliding dovetail tenon. The overall height of the top was 4". Subtract the 1-1/4" thick top and you get 2-3/4" for the supports. Then add in the height of the sliding dovetail tenons (1/2") and you have a final width of 3-1/4" for the supports. Cut those four parts to size now. 

CWHI_DecJan21_Zakarian_charcuterie_1
Sliding Dovetail Grooves – Zakarian routed four sliding dovetail grooves on the underside of the top. These grooves received the sliding dovetail tenons on the side of the four supports. Placement of these grooves isn’t critical, but will determine how wide the storage drawer is.
 
CWHI_DecJan21_Zakarian_charcuterie_2
Drawer Sub-Assemblies – Though you can install the supports and then add the back rail, Zakarian opted to bring the three parts together first. The length of the back rail has to be cut exactly to length if you go this route.
I used my Porter Cable jig to cut the sliding dovetails on the under­side of the top and all four drawer support pieces. There are many ways to cut sliding dovetails. If you don’t have a jig, rout the four sliding dovetail grooves in the underside of the top first, then install the same router bit in your router table and carefully adjust the height to allow you to router the sliding dovetail tenons. 
 
As for the spacing between the sliding dovetails, I located the out­ermost supports 1-1/4" from either end. The two innermost supports can be positioned according to how wide you want the drawers.
 
With the dovetails compete and dry fit, I machined a drawer groove on the inner face of each of the supports. These 1/2" wide grooves are cut using the table saw and a dado set. I positioned these grooves 1/4" away from the bottom edge of the support. The drawer bottom will fit into these grooves and allow the drawer bot­tom and face to slide in and out.
 
Two back rails
So the drawer cavity isn’t left open on the back side, I added a simple back rail between the two supports at either end of the board. From simple to complex, there are lots of joinery options.
 
I chose simple, and used a butt joint strengthened by a pair of 1/4" dowels to hold each joint secure. These back rails are 2-3/4" high and are cut to length during assembly so they fit perfectly between the supports.
 
Two-piece drawer
The drawer bottom was glued up so it would fit between the two supports. I then planed it down to just under 1/2". This will allow the drawer to slide freely in the 1/2" wide groove in the sides of the supports. The two drawer fronts are also machined to size now, and a 1/2" groove is cut in the rear of the drawer front to accept the bottom. This joint will only be glued at the center 5" or so to allow the drawer bottom to shrink and swell with seasonal movement.

CWHI_DecJan21_Zakarian_charcuterie_3
Simple Drawer – This may be the simplest drawer in the world. A flat bottom inserts into a groove in the rear of the front. The sides of the bottom run in grooves in the side of the supports.
 
Dry fit and assembly
Once all the parts are complete, I double check everything with a dry fit before final glue-up and finishing. All the parts were sanded prior to the final glue-up. The assembly was quite simple. You can assemble two supports with a back rail, then install that assem­bly in the sliding dovetail grooves on the underside of the top first.  Another slightly different variation is to install each support, then add the back rail between them. The choice is yours. I chose to assemble two supports and one back rail, then added that assembly to the underside of the top.
 
Glue two supports with the mating back rail and fasten them. Next, partially install the support assembly into the front of the top, so only half of the length of each support is inside the sliding dovetail in the top. Apply glue to only the portion of sliding dove­tail that’s visible. This allows the top to move with the seasons, but keeps it in place. Repeat for the other side. 
At this stage the drawer faces can be glued to the drawer bottom and ensure the fit is perfect. 
 
The 3/8" × 3/8" drawer borders were made and attached to the sliding tray with glue. They help contain the drawer’s contents. By adding another cross strip to the borders, you can lock the utensils in place. If that’s the approach you’d like to take, countersink a small bolt into the underside of the borders, and install it with its head pointing downward. A mating hole can be drilled in the crosspiece, and a small wing nut can be added to hold the crosspiece in place. 

CWHI_DecJan21_Zakarian_charcuterie_4
Customize It – In order to keep his utensils from moving around, and to add a sleek finished look, Zakarian added a pair of walnut side rails, and a third cross rail to the interior of his drawers. A pair of small wing nuts are removed to access the utensils.
 
A handle is next. I shaped and attached a wooden handle, but a store-bought handle is also an option.
 
Finishing
I used a food grade oil from Ligna for a finish, but there are many other good options out there. Once a few coats are applied, and a rubber bum­per is added under each corner of the project, the charcuterie board is ready to be delivered to its new home and enjoyed.

CWHI_DecJan21_Zakarian_charcuterie_illo

CWHI_DecJan21_Zakarian_charcuterie_materials-list

CWHI_DecJan21_Zakarian_charcuterie_hardware-list


 
Robert Zakarian
 
ROBERT ZAKARIAN

 
 

Related Articles

Cutting Board

Kitchen Project: This cutting board, with the end grain showing on top, harkens back to the old style butcher block.

Build an Arched-Top Wall Mirror with Curved Drawers

Heirloom Project: This cherry and birdseye maple wall mirror will look great in a front entrance or hallway. It may appear to be a challenging project, but the construction is quite manageable when you break it down into smaller...

Chimney Cupboard

Cabinet Project